4Series RMB Hot Runner Controller Instruction Manual1.3 Specifications1.3.1 Operating LimitsAmbient Temperature 32°F to 131°F (0°C to 55°C)Relative Hu
5Series RMB Hot Runner Controller Instruction Manual2. Operation2.1 Front PanelRMB controllers with the optional 30 amp output TRIAC are wider than th
6Series RMB Hot Runner Controller Instruction Manual2.2 What Happens When You Power Up theControllerTurn on the controller by pressing the “I”end of t
7Series RMB Hot Runner Controller Instruction Manual2.3.5 View Setpoint, Output,and CurrentTo cycle through the lower line displays: Press the DISPLAY
8Series RMB Hot Runner Controller Instruction Manual2.4.3 Changing Tuning Parameters Values ManuallyTo change a tuning parameter value manually:1. Pu
9Series RMB Hot Runner Controller Instruction Manual3.1 Setting SwitchesThe factory switch settings are shownbelow.Location of DIP SwitchesSW2-switch
10Series RMB Hot Runner Controller Instruction Manual4.1 Prepare the Controller1. Unpack the RMB controller.2. Inspect the controller for damage.3. Ma
11Series RMB Hot Runner Controller Instruction Manualparallel the interactions expected while thecontrollers are in use.If you need to stop the Autotu
12Series RMB Hot Runner Controller Instruction ManualDisplayed Code Error Condition Operator Actionor MessageErr Calibration value corrupted. Cycle po
13Series RMB Hot Runner Controller Instruction Manual5.3 Ground Fault in Controller Output WiringThe RMB controller detects ground faultsin the contro
IIYou can reach our technicalsupport team by phoning216.367.7000 or visitingwww.ppe.com
14Series RMB Hot Runner Controller Instruction Manual5.7 Heater CurrentMonitoringThe present current output to the heater,expressed to the closest ten
15Series RMB Hot Runner Controller Instruction Manual6.2 Cleaning the Front PanelTo clean an RMB controller:1. Read the safety warnings above before y
16Series RMB Hot Runner Controller Instruction Manual3. Use a cotton cloth to gently and sparingly apply isopropyl alcohol to the front panel of the c
17Series RMB Hot Runner Controller Instruction Manual7. Frequently Asked Questions7.1 IntroductionBefore you call for technical support, please look a
IndexAalarms, 2, 5, 6At.OP parameter, 6, 7, 11automatic mode. See normal modeAutotune, 2, 6, 7, 10Autotune errors, 12, 14Autotune Operation parameter,
19Series RMB Hot Runner Controller Instruction ManualNNORMAL LED, 5normal mode, 2Oopen sensor, 13Out Shrt error message, 14output bad, 3, 14output dis
Two-Year Limited WarrantyTHIS EQUIPMENT IS WARRANTED TO BE FREE FROM DEFECTS OF MATERIAL ANDWORKMANSHIP. IT IS SOLD SUBJECT TO OUR MUTUAL AGREEMENT TH
21Series RMB Hot Runner Controller Instruction ManualNotes
Plastic Process Equipment, Inc.8303 Corporate Park DriveMacedonia, OH 440561.800.321.0562 • 216.367.7000FAX: 216.367.7022 • www.ppe.comPart #900M212U0
IIIUse of this equipment in a manner not specified by the manufacturer may impair protection provided by the equipment.In addition to presenting a pot
IVIf a controller shows signs of having been damaged during shipping, do not power up or install the controller. Save all packing materials and report
iTable of ContentsPrecautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I1 Introduction
iiSeries RMB Hot Runner Controller Instruction Manual7. Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1Series RMB Hot Runner Controller Instruction Manual1. Introduction1.1 About This ManualThis manual contains all the informationneeded to set up and o
2Series RMB Hot Runner Controller Instruction Manual1.2.3 PID Control withAutotuningIn normal (automatic) mode each SeriesRMB controller uses a single
3Series RMB Hot Runner Controller Instruction Manual1.2.6.2 Loop Break DetectionThe controller monitors the input change.If the input value does not c
Comments to this Manuals